通風管道制作技術的安裝準備

發(fā)布人：http://rdhw.com.cn   發(fā)布時間：2018-01-09 17:53:38

1、圖紙已經熟悉，并且經過圖紙會審。對建筑、結構和電氣、暖衛(wèi)施工圖中的管路走向、坐標、標高與通風管道之間跨越交叉在圖紙上出現的問題已經有解決方案。

1, are familiar with drawings, drawings and after. For building, structure and electrical and heating protection drawings, pipeline crossing, coordinate, elevation and ventilation pipeline crossing over and crossing problems on drawings have been solved.

2、材料表面油污應全部干凈，以免鐵銹或氧化物落于材料表面產生局部腐蝕。

2, the surface of the material should be cleaned completely, so as to prevent the rust or oxide from falling on the surface of the material to produce local corrosion.

3、必須有一個單獨的加工場地，為了不破壞鍍鋅鋼板外的保護膜，工作場地好鋪設木板或者橡膠板，保持場地清潔。

3, there must be a separate processing site. In order not to destroy the protective film outside the galvanized steel sheet, it is best to lay wooden boards or rubber sheets in the workplace, so as to keep the field clean.

4、已進行了施工技術交底，對風管制作的尺寸，采用的技術標準、接口及法蘭連接方法已經明確。并且已經作好施工交底記錄。

4. The construction technology has been carried out. The size of the wind pipe, the technical standard, the interface and the flange connection method have been made clear. And it has made good record of the construction.

根據風管長邊尺寸進行合適的選料。按正確的放樣進行制作。

Suitable materials according to the wind pipe edge size. Make it according to the correct lofting.

風管翻邊時，翻邊應留有不小于6mm的余量，翻邊不能遮住螺栓孔，咬口邊要用剪刀進行倒角或開角，且不開裂，形成弧形翻邊。若翻邊四角開裂，應采用錫焊或密封膠填補，防止風管漏風風管板材厚度小于1.2mm時可以采用聯合角或按扣式咬口，大于1.2mm時采用焊接。

When the air pipe is flanging, the margin should be kept not less than 6mm. Flanging can not hide the bolt hole. The edge should be chamfered or opened with scissors, and it will not crack and form arc flanging. If the four angle flanging cracking, by soldering or sealant fill, prevent wind tube leakages wind pipe plate thickness is less than 1.2mm can adopt the joint angle or stud bite, more than 1.2mm by welding.

風管成型后與法蘭連接采用鉚接，鉚釘距風管壁距離不得大于50mm，各鉚釘間距不得大于150mm。

After the pipe is formed, the rivet is connected with the flange, and the distance between the rivet distance from the wall of the wind pipe must not be more than 50mm, and the rivet spacing should not be more than 150mm.

以上的技術支持均由山東通風管道的提供，更多的精彩內容請點擊進入我們的網站：http://rdhw.com.cn我們的會有更多的內容與大家分享.

The above technical support is provided by Shandong ventilation pipe. For more exciting content, please click on our official website: http://rdhw.com.cn, we will have more contents to share with you.