濟南通風管向你介紹如何清理通風管道內的雜質

發布人：http://rdhw.com.cn   發布時間：2018-08-07 11:23:14

通風管道隨著使用時間的不斷增長，里面會堆積很多的雜質，這些雜質長期存儲在管道內，在運轉中會加快它的油凝結，溫渡過高，構成氣壓閥、液壓等部件的損壞，對正常運轉構成很大的影響。所以定期的對通風管道設備進行清理是非常有必要的。如何進行清理呢？西安偉業通風管道下面為您介紹下：
With the continuous increase of the use time, the ventilation pipe will accumulate a lot of impurities. These impurities are stored in the pipeline for a long time. In the operation, it will speed up its oil condensation, temperature exorbitant, the damage of the pressure valve, hydraulic and other components, which has a great influence on the normal operation. Therefore, regular cleaning of ventilation piping equipment is very necessary. How do you clean up? Xi'an Weiye ventilation pipe expert below introduces you:

當風管與風機銜接時，應在進出風口處加軟接頭，其軟接頭的斷面尺度應與風機進出風口共同。軟管接頭普通可采用帆布、人造革等材料，軟管長度不宜小于200，松緊度應適宜，柔性軟管可緩沖風機的振蕩。
When the air duct is connected with the fan, a soft joint should be added at the inlet and outlet of the fan, and the cross-sectional dimension of the soft joint should be the same as the inlet and outlet of the fan. The hose joint can be made of canvas, artificial leather and other materials. The hose length should not be less than 200, the elasticity should be suitable, and the flexible hose can cushion the vibration of the fan.
當風道與除塵設備、加熱設備等銜接前，應待設備裝置終了后，按理論測繪的圖紙中止預制和裝置。
When the air duct and dust removal equipment, heating equipment, etc. before the connection, should wait for the equipment after the end of the device, according to the theory of mapping drawings to stop the prefabrication and equipment.
濟南通風管道裝置時，進、出風日宜在風道預制時開出洞口，如需在裝置終了的風道上現開風口，其接口處應緊密。
When the air duct is made in Ji'nan, the inlet and outlet should be opened when the air duct is prefabricated. If the vent is needed in the end of the air duct, the interface should be close.
當運送含凝結水或含濕量較大的氣體時，其水平管道宜設有坡度，并在低點處接排水管。裝置時風道底部不宜呈現縱向接縫，對底部有接縫處應中止密封處置。
When transporting gas containing condensate or large moisture content, the horizontal pipeline should be provided with a slope, and the drainage pipe should be connected at the low point. The longitudinal joint is not suitable for the bottom of the duct, and the sealing treatment should be stopped for the joints at the bottom.
對運送易燃、易爆氣體的鋼板風道，在風道銜接法蘭處應裝置跨接線，并與靜電接地網銜接。
For the steel plate air duct conveying flammable and explosive gases, the connecting flange of the air duct should be connected with the electrostatic grounding grid.
當水平風道高度在4m以上時，裝置人員應系帶。腳手架或移動式支架上的跳板應固定好，跳板寬度應契合規范，在腳手架上的裝置人員宜攜東西袋，避免東西或電鉆等物掉落傷人。
When the height of the horizontal airway is above 4m, the installation personnel should fasten the seat belt. The springboard on the scaffold or the movable support should be fixed. The width of the springboard should be in accordance with the safety specification. The device personnel on the scaffold should carry the bag to avoid the thing or the electric drill.
雙吊桿支架在風道就位后，應保證橫擔平直，吊桿不改動，雙吊桿受力均勻。
When the double hanger bracket is positioned in the air duct, the cross arm shall be straight and the boom shall not be changed, and the double hangers should be evenly distributed.
通風管道較好是三個月進行一次清潔，這樣既可以保證平時正常的運轉，還可以延長通風管道的使用壽命，對于清潔這方面的問題還有不明白的，可以通過我們的官網電話咨詢我們，我們會及時給您回復。
The best ventilation pipe is three months to carry out a comprehensive cleaning, so that it can ensure normal normal operation, but also prolong the service life of the ventilation pipe, and do not understand the problem of cleaning this aspect. We can consult us by our official network telephone, we will respond to you in time.