通風管道生產過程中的失誤解決措施都有哪些？

發布人：http://rdhw.com.cn   發布時間：2020-03-24 16:20:24

通風管道是通風空調系統的重要組成部分。但是由于種種原因，可能會導致管道的處理問題，下面就來了解一下有哪些問題。

　　Ventilation duct is an important part of ventilation and air conditioning system. However, due to various reasons, it may lead to pipeline processing problems. Let's see what problems exist.

　　1. 加工材料不符合標準

　　1. Processing materials do not meet the standards

　　性能:板材表面不平整，厚度不均勻，有明顯的壓痕、裂紋、砂痕、疤痕、銹斑等。風道平面下沉，側面向外突出，有明顯變形。

　　Performance: the surface of the plate is not smooth and the thickness is not uniform, with obvious indentation, crack, sand mark, scar, rust spot, etc. The plane of air duct sinks, the side protrudes outwards, and there is obvious deformation.

　　影響:運行中風道泄漏，空調負荷增加，同時影響風的壽命和性能。

　　Impact: air duct leakage during operation, air conditioning load increases, while affecting the life and performance of the air.

　　原因:材質不合格，不能滿足生產風管的需要。

　　Cause: the material is unqualified, which can not meet the needs of production air duct.

　　措施:使用管道加工設備制作管道前，應先檢查材料廠證書、材料合格證、外觀厚度等，確保材料的可用性。

　　Measures: before using the pipeline processing equipment to make the pipeline, the material factory certificate, material certificate, appearance thickness, etc. shall be checked first to ensure the availability of materials.

　　二、風管翹曲角度和彎頭角度不允許

　　2、 Duct warping angle and elbow angle are not allowed

　　性能:矩形風管兩個相對平面，兩端不平行;折疊角度不直;對角線不相等;寬松的咬人。

　　Performance: two relative planes of rectangular air duct, the two ends are not parallel; the folding angle is not straight; the diagonal is not equal; loose biting.

　　影響:會使氣管連接力不均勻，安裝后氣管不直，法蘭墊片不緊，漏風系統，空調負荷損失，并縮短使用壽命。

　　Influence: it will make the connection force of air pipe uneven, the air pipe is not straight after installation, the flange gasket is not tight, the air leakage system, air conditioning load loss, and shorten the service life.

　　原因:板材落料放樣不準確;風道兩邊平行，對邊的紙長和寬度不相等。

　　Cause: the blanking and setting out of the plate are not accurate; both sides of the air duct are parallel, and the paper length and width on the opposite side are not equal.

　　措施:下料時，板材角度應嚴格保持正方形，并檢查各板材的長、寬、對角線，使其偏差控制在允許范圍內;板材落料后，風道對面的兩塊板材應重合，以檢查尺寸的準確性。

　　Measures: when blanking, the angle of the plate shall be strictly square, and the length, width and diagonal of each plate shall be checked to make its deviation within the allowable range; after blanking, the two plates opposite the air duct shall be overlapped to check the accuracy of the size.

　　因此，為了生產出實用耐用的風管，必須在風管加工設備運行前后進行充分的預置和運行準備，以保證無故障，減少不必要的損失。

　　Therefore, in order to produce a practical and durable high-quality air duct, it is necessary to carry out sufficient preset and operation preparation before and after the operation of the air duct processing equipment, so as to ensure no failure and reduce unnecessary losses.

　　以上就是對濟南通風管道生產過程中失誤的解決措施的詳細介紹，想要了解更多請點擊官網http://rdhw.com.cn

　　The above is a detailed introduction to the solutions to the mistakes in the production of Jinan ventilation pipeline. For more information, please click http://rdhw.com.cn