鍍鋅螺旋風管對于散裝物料的輸送要注意什么？

發布人：http://rdhw.com.cn   發布時間：2023-01-18 20:52:59

散裝物料的輸送。在一些通風管道加工工廠的生產過程中，需要輸送松散的顆粒，特別是比例較小的螺旋風管，如發泡塑料顆粒，成本低，效果好。螺旋風管是一種薄壁管，由金屬帶材卷制而成，圓形，無焊接，無漏氣，無漏水，多用于送風和散裝物料輸送，而不是傳統的白鐵管(即手工咬鐵管)。它是一種風管，全機制，直管不需要手動敲擊。

Transportation of bulk materials. In the production process of some ventilation pipe processing plants, loose particles need to be transported, especially spiral air ducts with small proportion, such as foamed plastic particles, which have low cost and good effect. The spiral air duct is a kind of thin-walled pipe, which is rolled from metal strip, round, non-welded, non-leaking, non-leaking, and mainly used for air supply and bulk material transportation, rather than the traditional white iron pipe (i.e. manual bite iron pipe). It is a kind of air duct with full mechanism. The straight pipe does not need to be knocked manually.

鍍鋅螺旋風管指酒店、、紡織、化纖、石油化工、機械制造、儀表、電子、醫藥、煙草、食品、倉儲、寫字樓及地鐵、人防、地下室等工程的送風、排風、排煙管道。它的厚度和規格可根據需要而變化，通常在連接時，鍍鋅螺旋風管的兩端都要外接。

Galvanized spiral air duct refers to the air supply, exhaust and smoke exhaust pipes of hotels, shopping malls, textiles, chemical fiber, petrochemical, machinery manufacturing, instruments, electronics, medicine, tobacco, food, storage, office buildings, subways, civil air defense, basement and other projects. Its thickness and specification can vary according to needs. Generally, both ends of galvanized spiral air duct shall be externally connected when connecting.

由于鐵皮加工在不同環境下容易發生反應，導致腐蝕和生銹。鋅在干燥的空氣中基本沒有變化。在潮濕的空氣中，鋅表面會產生致密的堿性碳酸鋅膜，因此在風管鐵皮上鍍一層鋅可以保護鐵皮。鍍鋅處理鈍化、染色或涂上護光劑后，可加強其保護性和裝飾性。

The iron sheet processing is prone to react in different environments, resulting in corrosion and rust. Zinc basically does not change in dry air. In humid air, a dense alkaline zinc carbonate film will be formed on the zinc surface, so a layer of zinc on the iron sheet of the air duct can protect the iron sheet. After passivation, dyeing or application of light protection agent, zinc plating can enhance its protection and decoration.

通風管道加工的過程中應該盡量避免出現縱向接縫，但是一定不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處，需要按照設計潔凈等級要求，然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側。

The longitudinal joints shall be avoided as far as possible during the processing of ventilation pipes, but the transverse joints must not occur. In addition, the seam of the ventilation pipe and the gap at the four corners need to be sealed with sealant according to the design cleanliness level. In addition, the sealing surface of the connection joint of the ventilation pipe plate should be set at the positive pressure side of the ventilation pipe wall.

鍍鋅螺旋風管

Galvanized spiral air duct

加工的時候，不能在通風管道內部設置加固框或者加固筋，因為這樣對于通風管道的質量會造成一定的影響。

During processing, the reinforcing frame or reinforcing bar cannot be set inside the ventilation duct, because this will have a certain impact on the quality of the ventilation duct.

通風管道加工不能采用S型插條和C型直角插條的連接方式，另外對于一些特殊的通風管道來說，還不能采用按扣式的咬口。

The connection mode of S-type and C-type right-angle inserts cannot be used for the processing of ventilation pipes. In addition, for some special ventilation pipes, the snap bite cannot be used.

通風管道制作完畢之后，還要用清洗液進行清洗，只有達到清洗標準之后，才可以及時封口。

After the fabrication of the ventilation pipe, it should be cleaned with cleaning fluid. Only after the cleaning standard is met can it be sealed in time.

玻璃纖維復合板風管端口為切割面時，在裝配法蘭連接件前應將管端切口面用膠帶或膠液進行封堵，才能防止玻璃纖維外露和飛散

When the air duct end of the glass fiber composite plate is the cutting surface, the cutting surface of the pipe end shall be sealed with adhesive tape or glue before assembling the flange connector, so as to prevent the exposure and dispersion of the glass fiber